DAPDigital AudioProcessorOwner’s ManualRPR O C E E D
10Finally, an infrared receiver and transmitter for remote control of the DAP ispositioned on the left side of the main display. Owners of learning re
116 POLARITYThe DAP is a non-inverting device—that is, digital inputs which indicate apositive voltage generate a positive analog output. Some recordi
12PR O C E E DRd a p by MADRIGAL AUDIO LABORATORIESaes/ebuanalog outputs~ ac mainsmains fuse:.5A (250V) slo-blo 5x20mmplease see bottom panel for vol
13123Pin 1: Signal groundPin 2: Signal + (non-inverting)Pin 3: Signal – (inverting)Connector ground lug: chassis groundRefer to your preamplifier’s op
144 AES/EBU DIGITAL INPUTThis input accepts digital audio conforming to the 110Ω AES/EBU digitalinterface standard (via a cable equipped with XLR-type
158 ST DIGITAL INPUTThis input accepts digital audio conforming to the ST optical (sometimescalled “AT&T”—ST is a trademark of AT&T and the co
16Caution! The Proceed DAP has been safety-tested and is designedfor operation with a three-conductor power cord. Do notdefeat the “third pin” or eart
17Using the DAPInput Selection The DAP has five digital inputs. Using the up/down buttons, you may scrollthrough the five inputs in either direction.
18Remote Control of the DAPThe DAP includes both an infrared receiver and an infrared transmitter. With thiscapability, it can “teach” a learning remo
19(If you are uncertain as to how to prepare your remote control for learningnew commands, refer to the instructions provided with the remote control.
CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DONOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.REFER SE
20The DAP will display a “L 00” code when it has entered its teaching modeand is ready to help the remote control learn the commands that corre-spond
21(If you are uncertain as to how to prepare your remote control for learningnew commands, refer to the instructions provided with the remote control.
22Care & MaintenanceTo remove dust from the cabinet of the DAP, use a feather duster. To remove dirtand fingerprints, we recommend isopropyl alcoh
23U.S. and Canadian Warranty90-Day Limited Warranty This Proceed® product is warranted to be free from defects in material and work-manship under norm
24Obtaining ServiceWe take great pride in our dealers. Experience, dedication, and integrity makethese professionals ideally suited to assist with our
25SpecificationsThe correlation between published specifications and performance is unreliable. Alist of numbers reveals virtually nothing. All techni
26Dimensions12.27"31.2cm0.98"2.49cm13.25"33.7cm13.25"3.5"8.9cm13.25"33.7cmPR O C E E Dd a pstandbymute17.25"43.8cm1
27
630408 © 12/1999 Madrigal Audio Laboratories, Inc. All rights reserved. Printed in U.S.A.RPR O C E E Dis a registered trademark of Madrigal Audio Labo
Important Safety InstructionsPlease read all instructions and precautions carefully and completely before operating your DAP digital audioprocessor.1.
4From all of us at Madrigal Audio Laboratories, thank you for choosing theProceed DAP digital audio processor.A great deal of effort went into the des
5Table of ContentsUnpacking and Placement ... 6Unpacking ...
6Unpacking and PlacementUnpacking Unpack your Proceed® DAP digital audio processor and keep all packing mate-rials for future transport. Locate and re
7Operating VoltageThe DAP digital audio processor is set at the factory (internally) for 100V, 120V,200V, 220V, or 240V AC mains operation as appropri
8Special Design FeaturesCongratulations on your purchase of the Proceed DAP. The Madrigal design teamis confident you will enjoy the outstanding perfo
9PR O C E E Ddappowermutemodepolarity2 3 4 561Front Panel1 STANDBY & STANDBY LEDAssuming that the DAP’s power cord is connected to AC power, press
Kommentare zu diesen Handbüchern